Mining and concentrating
Our editors will review what you’ve submitted and determine whether to revise the article.
- Related Topics:
- tin
- materials processing
Vein deposits, such as those in Bolivia and the United Kingdom, usually occur in granite formations and are recovered by conventional underground hard-rock mining techniques. In deep mines, primary crushing equipment is usually located underground in order to reduce the ore to a manageable size before transportation to the surface.
The more productive alluvial fields are relatively shallow deposits of fine-grained minerals that have accumulated in ancient riverbeds or valleys. They are mined by one of several surface-mining methods, principally gravel pumping, dredging, and, to a smaller extent, open-pit mining. A large proportion of tin ore is mined by gravel pumping. In this method, the barren overburden is removed, often by draglines or shovels, and high-pressure water jets are used to break up and dislodge the tin-bearing sand. A submerged gravel pump then sucks up the slurry of mud and water and raises it to a series of sluice boxes, or palongs, which slope downward and have baffles placed at intervals along their length. As the slurry flows along, the heavier minerals, including cassiterite, fall to the bottom, while the lighter waste material flows over the end of the boxes to tailings dumps. Periodically the flow is stopped and the crude concentrate removed.
In places where water is plentiful, an area above an alluvial deposit is flooded, often by diverting a river, and a mining dredge floated on it. Dredges have endless bucket chains at one end that dig and lift the tin-bearing ore to the primary processing plant, which is usually located on board. Ores are concentrated by gravity separation methods, including jigs and shaking tables. The concentrate is then collected for further treatment onshore, while the barren material is discharged over the stern of the dredge.
Tin concentrates from the alluvial mining areas of Southeast Asia are relatively free of impurities, although there may be small quantities of related minerals such as wolframite, scheelite, and columbite. Concentrates shipped to the smelter usually contain 70 to 75 percent tin metal. On the other hand, the complex sulfide ores found in underground deposits, such as those of Bolivia, require more complicated mineral processing, often involving froth flotation, in order to produce a clean tin concentrate. Even then, Bolivian concentrates may average only 50 to 60 percent tin.
Extraction and refining
Smelting
Before being smelted, low-grade concentrates from complex ores are first roasted in a reverberatory or multiple-hearth furnace at temperatures between 550 and 650 °C (1,025 and 1,200 °F) to drive off the sulfur. Depending on the type and quantity of impurities, oxidizing, reducing, or chlorinating reactions take place. Roasting is frequently followed by leaching with water or acid solutions to remove impurities made soluble by roasting.
After appropriate preparation, the furnace feed for smelting comprises tin oxide and some impurities, including iron oxides, that were not removed in mineral processing or roasting.
Tin smelting furnaces are one of three basic types: reverberatory furnaces, blast furnaces, or electric furnaces. Usually the operation is carried out as a batch process.
The principle of tin smelting is the chemical reduction of tin oxide by heating with carbon to produce tin metal and carbon dioxide gas. In practice, the furnace feed contains the tin oxide concentrate, carbon in the form of anthracite coal or coke, and limestone to act as a flux and a slag-producing agent.
In a typical reverberatory process (the most commonly used), the furnace is heated to 1,300–1,400 °C (2,375–2,550 °F) for a period of some 15 hours, during which it is stirred frequently, especially during the later stages. This process produces a pool of molten tin, on top of which floats a slag containing most of the unwanted impurities.
At the completion of smelting, the impure tin is tapped off and cast into large slabs, while the slag is solidified into granules by being poured into water tanks. The impure tin slabs go for further refining, and the granulated slag, which may still contain some tin, is retreated.
Refining
There are two methods of refining impure tin. Fire refining is most commonly used and produces tin (up to 99.85 percent) suitable for general commercial use. Electrolytic refining is used on the products of complex ores and to produce a very high grade of tin (up to 99.999 percent).
One fire-refining method is called boiling. In this, impure tin from the smelter, or tin from the liquation furnace (see below), is heated in vessels or kettles that are agitated by compressed air. The effect is to oxidize the impurities, which rise to the surface and form a dross.
Another fire-refining method is liquation. Used to treat both impure tin and dross from smelting, it removes those impurities that have a higher melting temperature than tin. The materials to be treated are placed on a sloping hearth in a reverberatory furnace and heated to a temperature just above the melting point of tin. The tin melts slowly and runs down the slope, to be collected in a vessel, leaving the unmelted residues on the hearth. These are subsequently removed and treated.
Vacuum distillation is sometimes used in fire refining. In this process, molten tin is heated in a dense graphite vessel at high temperatures (1,100 to 1,300 °C, or 2,000 to 2,375 °F). A vacuum is applied, and impurities are removed by selective distillation at their respective boiling temperatures.
In electrolytic refining, impure tin is cast into anodes. These are placed into an acidic electrolyte with starting cathodes made of thin sheets cast from high-purity tin. Special agents are required in the electrolyte in order to obtain dense, compact cathode deposits. After a period of about a week, the cathodes are removed.
Tin is normally sold in the form of ingots, or pigs, which are cast from refined tin. Most metallic tin is produced at smelters and refineries located near mining areas.
Secondary tin
Important sources of tin scrap are used bearings, solder alloys, or bronzes. Frequently, it is economic not to recover high-grade tin from these but to use the tin-containing scrap to produce alloys directly.
Tin residues may be treated like tin concentrates and smelted and refined as described above. Electrolytic refining is frequently employed for secondary-tin production.
Tinplate, whether as clean can-makers’ scrap or from used cans, is another source of secondary tin. The tinplate is detinned electrolytically to produce a high grade of tin and a clean steel scrap, which is returned to steelmakers.