Intermodal freight vehicles and systems

Development

Initially, the emphasis in North America was on the rail piggybacking of highway trailers on flatcars (TOFC), which the Southern Pacific Railroad pioneered in 1953. By 1958 the practice had been adopted by 42 railroads; and by the beginning of the 1980s U.S. railroads were recording more than two million piggyback carloadings a year. In Europe, few railroads had clearances ample enough to accept a highway box trailer piggybacked on a flatcar of normal frame height. As shipping lines developed their container transport business in the early 1960s, European railroads concentrated initially on container-on-flatcar (COFC) intermodal systems. A few offered a range of small containers of their own design for internal traffic, but until the 1980s domestic as well as deep-sea COFC in Europe was dominated by the standard sizes of maritime containers. In the 1980s an increasing proportion of Europe’s internal COFC traffic used the swapbody, or demountable, which is similar in principle to, but more lightly constructed, cheaper, and easier to transship than the maritime container; the latter has to withstand stacking several deep on board ship and at ports, which is not a requisite for the swapbody. As its name suggests, the swapbody has highway truck or trailer body characteristics.

The container took on a growing role in North American intermodal transportation in the 1980s. American President Intermodal decided that containers originating from Pacific Rim countries to destinations in the Midwest and eastern United States were better sent by rail from western seaboard ports than shipped through the Panama Canal. To optimize the economics of rail landbridging, the shipping line furthered development of lightweight railcars articulating five low-slung well frames on each of which containers could be double-stacked within, or with minimal modification of, the vertical clearances of the principal route between West Coast ports and Chicago. At the same time, the shipping line marketed containers off-loaded in the east as the medium for rail shipment of merchandise from the east to the western states. This was influential in stimulating new interest in the container as a medium for domestic door-to-door transportation. Other shipping lines copied American President’s lead; railroads enlarged clearances to extend the scope of double-stack container transportation to the eastern and southern seaboards (Canadian railroads followed suit); and in the later 1980s both double-stack operation and the container’s share of total North American intermodal traffic rapidly expanded.

Operations

The overhead costs of COFC and TOFC are considerable. Both require terminals with high-capacity transshipment cranage and considerable space for internal traffic movement and storage. TOFC also has a cost penalty in the deadweight of the highway trailers’ running gear that has to be included in a TOFC train’s payload. Two principal courses have been taken by railroads to improve the economics of their intermodal operations. One is to limit their transshipment terminals to strategically located and well-equipped hubs, from which highway collection and delivery services radiate over longer distances; as a result, the railroad can carry the greater part of its intermodal traffic in full terminal-to-terminal trainloads, or unit trains. The other course has been to minimize the tare weight of rail intermodal vehicles by such techniques as skeletal frame construction and, as in the double-stack COFC units described above, articulation of car frames over a single truck. Even so, North American railroads have not been able to make competitively priced TOFC remunerative unless the rail component of the transit is more than about 1,000 km (600 miles).

Two different managerial approaches to intermodal freight service have developed in the United States. Some of the major railroads have organized to manage and market complete door-to-door transits themselves; others prefer simply to wholesale intermodal train space to third parties. These third parties organize, manage, and bill the whole door-to-door transit for an individual consignor.

Given the shorter intercity distances, European railroads have found it more difficult to operate viable TOFC services. The loading of a highway box trailer on a railcar of normal frame height without infringing European railroads’ reduced vertical clearances was solved by French National Railways in the 1950s. The answer was a railcar with floor pockets into which the trailer’s wheels could be slotted, so that the trailer’s floor ended up parallel with that of the railcar. Even so, there were limitations on the acceptable height of box trailers. Other railroads were prompted to begin TOFC in the 1960s when the availability of heavy tonnage cranes at new container terminals simplified the placing of trailers in the so-called “pocket” cars. Initial TOFC service development was primarily over long and mostly international trade routes, such as from the Netherlands, Belgium, and northern Germany to southern Germany, Austria, and Italy.

In 1978 the West German government decided to step up investment in its railways for environmental and energy-saving reasons. Its plans included a considerable subsidy of railroad intermodal operation, including TOFC. Similar support of intermodal development, for the same reasons, was subsequently provided for their national railways by the Austrian and Swiss governments. The German railroad (and also Scandinavian railroads) has more generous vertical clearances than the European norm. Whereas other European mainland railroads, even with pocket cars, can only operate TOFC over a few key trunk routes, the German Federal Railway Authority could use the financial support to launch TOFC as well as COFC service between most of its major production and consumption areas.

The Germans, followed by the Austrians and Swiss and then other European countries, developed a particularly costly intermodal technology called “Rolling Highway” (Rollende Landstrasse), because it employs low-floor cars that, coupled into a train, form an uninterrupted drive-on, drive-off roadway for highway trucks or tractor-trailer rigs. Rolling Highway cars are carried on four- or six-axle trucks with wheels of only 36-cm (14-inch) diameter so as to lower their floors sufficiently to secure the extra vertical clearance for highway vehicles loaded without their wheels pocketed. Platforms bridge the gap between the close-coupled railcars. To allow highway vehicles to drive on or off the train yet enable a locomotive to couple to it without difficulty, the train-end low-floor cars have normal-height draft-gear headstocks that are hinged and can be swung aside to open up the train’s roadway. Truck drivers travel in a passenger car added to the train.

In the face of growing trade between northwestern and southeastern Europe, Austria and Switzerland have imposed restraints on use of their countries as a transit corridor by over-the-highway freight to safeguard their environments. Primarily to provide for increase in intermodal traffic, and in particular Rolling Highway trains, the Swiss parliament approved a government plan to bore new rail tunnels on each of its key north-south transalpine routes, the Gotthard and the Lötschen. The Lötschberg Base Tunnel, the world’s longest overland tunnel—a 34.6-km (21.5-mile) rail link—took eight years to build, and when full rail service began in 2007, it slashed the train journey between Germany and Italy from 3.5 hours to less than 2 hours. The 57-km (35-mile) Gotthard Base Tunnel—an even more ambitious project—was opened June 1, 2016, and was the longest and most deeply set rail tunnel in the world. Both tunnels are much longer than older tunnels located higher up in the summit passes, and their tracks are free of the summit routes’ steep gradients and sharp curves on either side of their tunnels.

Passenger intermodals

To save motorists the negotiation of mountain passes, especially in winter, two Swiss railroads shuttle drive-on, drive-off trains for automobiles between terminals at the extremities of their transalpine tunnels. This practice has been elaborated for Channel Tunnel rail transport of private automobiles, buses, and trucks between Britain and France. The tunnel’s rail traffic is partly conventional trains, but it has been bored to dimensions that allow auto transporter trains to employ cars of unprecedented size. Consequently, these trains are limited to shuttle operation between terminals on the British and French coasts. The fully enclosed double-deck cars for automobile traffic measure 5.5 metres (18 feet 4 inches) high and 4 metres (13 feet 5 inches) wide; the latter dimension allows room for automobile passengers, who are carried in their vehicle, to dismount and use the car’s toilet or auto-buffet while the train threads the tunnel. The transporter cars for buses and trucks are single-deck.