Coupling amplifiers
- Key People:
- Lei Jun
- An Wang
- Robert Morris Page
- Walter Schottky
- Related Topics:
- physics
- industry
- electronic system
- On the Web:
- Society of Photographic Instrumentation Engineers - Introduction to Electronics (Oct. 25, 2024)
News •
The existence of more than one type of transistor gives the circuit designer additional freedom not available for vacuum tube circuits and allows many clever circuits to be constructed. This becomes apparent in the direct coupling of successive amplifier stages. There are many ways to couple a signal from one circuit to another. Each has its advantages and disadvantages. Consideration must be given to the voltage levels in the circuits. In cases where the voltage level at the collector of the first amplifier is different from that at the base of the second, a direct connection could not be used. A transformer could be employed for coupling, with its primary in the collector circuit of the first amplifier and its secondary in the base circuit of the second one. However, transformers often do not exhibit uniform behaviour over a wide range of frequencies, which can be a problem. Transformers also are expensive and bulky. Similarly, a capacitor could be inserted between the collector of the first amplifier and the base of the second. This works well for many applications, providing uniform coupling inexpensively over a wide frequency range. At low frequencies, capacitive coupling becomes ineffective, however.
The use of a p-n-p second amplifier allows direct connection between the amplifiers (see ). If properly designed, this arrangement provides useful amplifying properties from DC to quite high frequencies. Care is required to avoid any changes in the DC operating conditions of the first amplifier; such changes will cause an amplified change in the DC conditions of the second one. Changes in temperature, in particular, can cause changes in resistor values and changes in the amplification properties of transistors. These factors must be carefully taken into account. Judicious use of feedback from later parts of a circuit to earlier ones can be utilized to stabilize such circuits or to perform various other useful functions (see below Oscillation). In negative feedback, the feedback signal is of a sense opposite to the signal present at the point in the circuit where the feedback signal is applied. While this has the effect of reducing the overall gain of the circuit, it also corrects numerous small distortions that may have occurred in the signal. For example, if the amplifier does not amplify large signals as much as small ones, the feedback from larger signals will be less, as will the reduction in gain, and the larger signals will be increased in the output of the circuit. Thus the distortion is reduced.
Oscillation
If feedback is positive, the feedback signal reinforces the original one, and an amplifier can be made to oscillate, or generate an AC signal. Such signals are needed for many purposes and are created in numerous kinds of oscillator circuits. In a tunable oscillator, such as that required for a radio receiver, the parallel combination of an inductor and a capacitor is a tuned circuit: at one frequency, and only one, the inductive effects and the capacitive effects balance. At this frequency the voltage developed across the tuned circuit is a maximum. Positive feedback is provided by the inductor in the collector circuit, which is magnetically coupled to the inductor of the tuned circuit. The connections to these inductors are arranged so that, when the collector current increases, the voltage at the base also increases, thus causing the collector current to rise further. The action of the tuned circuit reverses this sequence after a time and causes the base voltage to start to fall. This reduces the collector current; the positive feedback then further reduces the base voltage, and so on.
The circuit is in fact an amplifier whose output provides the input signal. The tuned circuit affects the feedback process in such a way that the circuit responds to an input signal at only one frequency—namely, the frequency to which the inductor and capacitor are tuned. The variable capacitor provides a way to adjust the frequency of oscillation. The output signal is obtained from the emitter resistor, through which the current rises and falls in synchrony with the collector current.
Oscillators that produce a single, accurate frequency are often needed. Such an oscillator is used in electronic watches. Other circuits in the watch count the output signals from the oscillator to determine the passage of time. These oscillators use a quartz crystal instead of a tuned circuit to establish the operating frequency (see ).
Quartz has the useful properties of changing its dimensions slightly if an electric field is applied to it and, conversely, of producing a small electrical voltage when pressure is applied (the piezoelectric effect). In a quartz-crystal oscillator a small plate of quartz is provided with metal electrodes on its faces. Just as a bell rings when struck, the quartz plate also “rings,” but at a very high frequency, and produces an AC voltage between the electrodes at this mechanically resonant frequency. When such a crystal is used in an oscillator, positive feedback provides energy to the quartz crystal to keep it ringing, and the oscillator output frequency is precisely controlled by the quartz crystal.
Quartz is not the only crystalline material that exhibits a piezoelectric effect, but it is used in this application because its oscillation frequency can be quite insensitive to temperature changes. Quartz-controlled oscillators are able to produce output frequencies from about 10 kilohertz to more than 200 megahertz and, in carefully controlled environments, can have a precision of one part in 100 billion, though one part in 10 million is more common.