Physical and chemical aspects of combustion

The chemical reactions

Combustion, with rare exceptions, is a complex chemical process involving many steps that depend on the properties of the combustible substance. It is initiated by external factors such as heat, light, and sparks. The reaction sets in as the mixture of combustibles attains the ignition temperature. The combustion spreads from the ignition source to the adjacent layer of gas mixture; in turn, each point of the burning layer serves as an ignition source for the next adjacent layer, and so on. Combustion terminates when equilibrium is achieved between the total heat energies of the reactants and the total heat energies of the products. Most reactions terminate when what is called thermal equilibrium has been attained—i.e., when the energy of the reactants equals the energy of the products.

A relationship exists between the ignition temperature and the pressure of the mixture under specific conditions. The figure shows the relationship for a mixture of hydrogen and oxygen. Only one temperature corresponds to a given pressure, whereas one or three pressures, called the explosion limits, may correspond to one temperature. The mechanism of the reaction determines the explosion limits: the reaction can proceed only when the steps in the sequence of reactions occur faster than the terminal steps. Thus, for combustion to be initiated with light or with a spark, the light intensity or the spark energy must exceed certain minimal values.

The complexity of the combustion reaction mechanism and the rapidly varying temperatures and concentrations in the mixture make it difficult and often impossible to derive an equation that would be useful for predicting combustion phenomena over wide temperature and concentration ranges. Instead, use is made of empirical expressions derived for specific reaction conditions.

Special combustion reactions

Reactions of oxygen with hydrogen, with carbon monoxide, and with hydrocarbons are most important from the standpoint of theory and, at the same time, are of great practical value.

Hydrogen combustion proceeds by complicated branched-chain reactions involving the interaction of hydrogen and oxygen atoms with oxygen and hydrogen molecules, respectively, to produce hydroxyl radicals. The final reaction product is water, formed by the combination of hydroxyl with hydrogen molecules. Reactions that terminate the chain, such as recombination of atoms and fragments of molecules, and the adsorption of active particles on solid surfaces, also play an important part in the mechanism of hydrogen combustion. The knowledge of rate constants for these processes derived empirically makes possible a quantitative description of all combustion characteristics, such as explosion limits, delay of ignition, and burning velocity.

Britannica Quiz

Types of Chemical Reactions

Combustion of carbon monoxide is mainly restricted to mixtures containing hydrogen or hydrogen compounds. In this case the reaction mechanism differs from that of hydrogen combustion chiefly in that it involves a step of fast interaction between hydroxyl and carbon monoxide.

Pure mixtures of carbon monoxide and oxygen (or air) can be ignited only with sparks of high energy or under high pressures and temperatures. The chemical mechanism of their combustion is not yet clear, probably because oxidation of carbon monoxide, a reaction that is part of the combustion of practically all natural fuels, usually occurs in the presence of hydrogen or hydrogen compounds: the breakdown of wood, coal, petroleum, etc., during burning produces carbon monoxide, hydrogen, and compounds of carbon and hydrogen.

The mechanisms of combustion of hydrocarbons and of other organic compounds are known in general outline only. Many elementary steps of hydrocarbon combustion involving oxygen and hydrogen atoms, hydroxyl, and organic radicals are similar to those for hydrogen; however, the overall mechanism of hydrocarbon combustion is complicated by the diversity of molecules and radicals involved. Moreover, with oxidation, thermal decomposition, a breakdown of complex organic compounds without oxidation, also takes place.

Two types of hydrocarbon combustion have been defined: (1) slow combustion at temperatures below 500 °C, including cool flames observed at certain pressures, and (2) combustion at higher temperatures, accompanied by hot flames. Ignition in two stages is characteristic of higher hydrocarbons, in which a cool-flame stage yielding readily oxidizable products precedes that of the hot flame.

Physical processes

In addition to chemical reactions, physical processes that transfer mass and energy by diffusion or convection occur in gaseous combustion. In the absence of external forces, the rate of component diffusion depends upon the concentration of the constituents, pressure, and temperature changes, and on diffusion coefficients (a measure of the speed of diffusion). The latter are either measured or calculated in terms of the kinetic theory of gases. The process of diffusion is of great importance in combustion reactions, in flames—that is, in gaseous mixtures, and in solids or liquids. Diffusion heat transfer (by molecular means) follows a law (Fourier’s law) stating that the heat flux (a measure of the quantity of heat) is proportional to the temperature gradient (the difference in temperature between two limiting temperatures). The coefficient of proportionality, called the thermal conductivity coefficient, is also measured or calculated in terms of the kinetic theory of gases, like the diffusion coefficient.

Convective transport of mass and energy may be accounted for by buoyant forces, external forces, and turbulent and eddy motions. Convection is in the main responsible for the mixing of gases (e.g., in furnaces).

Sublimation (the direct evaporation of a solid without intermediate liquid stage), evaporation of liquids, and the mechanical destruction of burning samples, all methods of transforming solids and liquids into gases, greatly contribute to their ease of combustion. In general, the combustion of condensed systems—i.e., liquids and solids—is more complex than that of gases, which accounts for the greater development of the gas combustion theory.

Energy transport in combustion may also occur by the emission of light, mostly in the infrared.