- Related Topics:
- materials processing
- vacuum
- leakage
- vacuum pump
- vacuum gauge
This pump is mainly used on equipment for the study of clean surfaces and in radio-frequency sputtering. Capacities are available up to 190,000 cu ft per minute with an operating pressure range of 10-2 to less than 10-9 torr when water-cooled baffles are used and less than 10-11 torr when refrigerated baffles are employed. The pumping speed for a vapour pump remains constant from about 10-3 torr to well below the ultimate pressure limitations of the pump fluid—that is, with the best fluids to pressures of better than 10-9 torr. The diffusion pump is initially evacuated by an oil-sealed rotary pump to a pressure of about 0.1 torr or less. When the pump fluid in the boiler is heated, it generates a boiler pressure of a few torr within the jet assembly. High-velocity vapour streams emerge from the jet assembly, impinge and condense on the water- or air-cooled pump walls, and return to the boiler. In normal operation a portion of any gas arriving at the inlet jet is entrained, compressed, and transferred to the next stage. This process is repeated until the gas is removed by the mechanical forepump.
Sputter ion pump
Capacities are available up to 14,000 cu ft per minute, with an operating pressure range of 10-2 torr to below 10-11 torr. The full speed of the pump is developed in the pressure range from about 10-6 to 10-8 torr, although the characteristic at the lower pressure is dependent on pump design. This pump makes use of the sputtering principle, in which a cathode material such as titanium is vaporized—or sputtered by bombardment with high-velocity ions. The active gases are pumped by chemical combination with the sputtered titanium, the inert gases by ionization and burial in the cathode, and the light gases by diffusion into the cathode.
A typical pump consists of two flat rectangular cathodes with a stainless steel anode between them made up of a large number of open-ended boxes. This assembly, mounted inside a narrow box attached to the vacuum system, is surrounded by a permanent magnet. The anode is operated at a potential of about seven kilovolts (kV), whereas the cathodes are at ground potential.
Sputter ion pumps have a long life and can provide ultrahigh vacuum, free of organic contamination and vibration. They are employed mainly for clean-surface studies and in those applications where any organic contamination will give unsatisfactory results.
Titanium sublimation pump
Capacities are available up to many thousands of cu ft per minute, operating in the pressure range of 10-3 to below 10-11 torr. The full speed of the pump, which only pumps chemically reactive gases, is developed at pressures below 10-5 torr. In this type of pump, titanium is sublimed onto the pump walls from either a resistance or an electron-beam heated source. Active gases are pumped by chemical combination, but inert gases are not pumped. As a consequence, it must always be used in conjunction with a diffusion or sputter ion pump. At pressures below 10-5 torr the film will be deposited faster than it is being consumed, allowing deposition to be carried out at intervals rather than on a continuous basis. Sublimation pumps are generally used in conjunction with a sputter ion pump in applications where a high speed is required and freedom from organic contamination is essential, as in the evaporation of materials onto a clean surface.
Sorption pump
Typically, the size of these pumps is about 1,000 grams of sorbent material, which retains gas molecules on its surface. They are capable of pumping from atmosphere to 10-2 torr or can be used in series down to 10-5 torr. In most cases the sorbent material is a molecular sieve—that is, a material that has been processed so that it is porous, with pore sizes comparable to the size of molecules, although activated charcoal can also be employed. The sorbent is positioned inside a cylindrical container that is connected to the vacuum system and that can be immersed in liquid nitrogen for supercooling to aid the sorption process. The gas is released when the sorbent returns to room temperature. This pump is used mainly for roughing systems in which the sputter ion and titanium sublimation pumps serve to ensure freedom from organic contamination.
Cryopump
This type of pump utilizes extremely low temperatures to condense gases and thus remove them from the system. Pumping speeds of millions of cu ft per minute are possible with the cryopump over the pressure range 10-3 torr to well below 10-10 torr. This type of pump can develop its full speed curve over the entire pumping range. Most cryopumps employ helium to cool the low-temperature surface; the helium can be in the form of gas at about 15 K or liquid helium at 4.2 K. A cryopump, which depends on the condensation of the gas for its pumping speed, will not effectively pump gases, such as helium and hydrogen, that have high vapour pressures at the low-temperature surface. Consequently, complementary diffusion or sputter ion pump capacity is a necessary adjunct to a cryopump vacuum-producing system. Most such pumps are used in high-altitude or space simulation.