Production specifications
Our editors will review what you’ve submitted and determine whether to revise the article.
These include specifications for line plates, halftone specifications, and combination plates.
Line plates
In line illustrations all of the image areas are either black or white, and hence no halftone screen is required to copy them for use in making a printing plate. Suitable copy consists of line drawings, etchings, etc. The negative as it comes from the process camera is suitable to transfer the line image onto the metal.
Plate preparation, coating, burning in, etching, and finishing are essentially the same as for halftone plates. Certain specifications must be met, however. The nonprinting areas must be etched sufficiently deep to prevent the ink rollers from touching them on the press, and to prevent them from rubbing on the surface of the paper during wet colour printing. For presses with accurately adjustable ink rollers, the etch depth may be as little as 0.01 inch. The same depth is permissible in thin, wraparound press plates. For conventional printing presses, the minimum etch depth is about twice this. Plates that are to be duplicated by electrotype or stereotype processes may require slightly greater depths, although normal etching ordinarily is sufficient to produce good duplicates. Plates from which rubber duplicates are to be made will require etch depths as great as 0.045 inch.
Halftone specifications
Etch depths in halftone plates need not be as great as those in line plates, but the contour of the halftone dot and the depth of the etched areas are very important. Etch depth in highlight areas, the most critical portions of halftones, varies from 0.006 inch in a 65-line halftone to 0.002 inch in a 133-line.
Combination line-and-halftone plates
These plates must be prepared by assembling, in the negative form, the halftone and the line portions of the illustration and then, after transferring them onto the metal, etching them in two operations, so as to attain the best results for both portions. The powderless etching processes, however, permit easier etching of coarse-screen combination plates for use in newspapers. Combination line-and-halftone plates may also be produced by making two plates in separate operations and mounting them on a single block in proper position with respect to each other.
Engraving techniques applied to intaglio processes
Procedures similar to those described for production of letterpress printing surfaces are applicable to the production of intaglio printing surfaces. In intaglio, or gravure, printing, the image to be transferred to paper is etched or incised into the surface of the printing plate or cylinder. The entire surface is covered with ink, and by means of a doctoring, or wiping, operation, excess ink is removed from the surface, leaving only that which is retained in the image areas. Paper is brought into contact with the surface, and, under high mechanical pressures, the ink transfers from plate to paper.
Intaglio printing surfaces are of two general types: line intaglio (sometimes referred to as copperplate gravure), in which the ink-retaining image consists of discrete lines that may vary in width and depth; and gravure (also known as rotogravure), in which both continuous-tone and line copy are reproduced as a series of tiny cells etched into the printing surface. These cells commonly vary in depth, and hence in the volume of ink they will retain. Variations in density are produced on paper by the different amounts of ink that the cells transfer to paper.
In the rotogravure printing process, the walls surrounding each cell act as a support for the doctor blade that removes ink from the printing cylinder or plate surface.
Line intaglio
This process is widely used in the production of bank notes, securities, stamps, and engraved documents. The distinctive sharpness of fine lines and readily discernible differences in ink thickness that the process produces make it a preferred technique for production of bank notes and securities. These appearance characteristics cannot be readily counterfeited by photomechanical processes.
The printing surface is created either by mechanically scratching an acid-resistant ground from the plate surface, as described above, or by use of a photographic positive of the desired line pattern to prepare a photoresist image on the metal. The image is etched into the plate, using the techniques of letterpress line etching, with maximum depth of etch usually less than 0.007 inch. Metals commonly used include steel, brass, and copper.
When a mechanical engraver is used to expose the metal for etching, a pointer or stylus is used to follow a usually enlarged pattern in a metal or plastic master stencil, causing a diamond stylus, which is in contact with the lacquer-covered plate surface, to remove the lacquer in a sharply defined pattern. The intaglio image is then prepared by etching the exposed metal with the appropriate chemicals.
In printing from intaglio forms, the plate is flooded with an ink of medium viscosity and the surface of the plate wiped clean with either a metal doctor blade or a piece of hard-surfaced paper. To minimize wear of the plate from the abrasion of the wiping mechanism, the surface is ordinarily protected by an electroplated chromium layer.
Wiped free of excess ink, the plate is brought into contact with the paper surface. A roughly outlined relief image (counter) of the printing pattern is often used to provide high local pressures, forcing the paper into the ink-filled intaglio image. As the paper is pulled from the plate, capillary-attraction and surface-tension forces act to pull the ink from the plate. After drying, the image has a distinctive appearance in which the ink has appreciable thickness, and thin lines have less thickness than wider lines.