Off-sites
- Related Topics:
- cracking
- alkylation
- reforming
- petroleum refinery
- desulfurization
The individual processing units described above are part of the process-unit side of a refinery complex. They are usually considered the most important features, but the functioning of the off-site facilities are often as critical as the process units themselves. Off-sites consist of tankage, flare systems, utilities, and environmental treatment units.
Tankage
Refineries typically provide storage for raw materials and products that equal about 50 days of refinery throughput. Sufficient crude oil tankage must be available to allow for continuous refinery operation while still allowing for irregular arrival of crude shipments by pipeline or ocean-going tankers. The scheduling of tanker movements is particularly important for large refineries processing Middle Eastern crudes, which are commonly shipped in very large crude carriers (VLCCs) with capacities of 200,000 to 320,000 tons, or approximately two million barrels. Ultralarge crude carrier (ULCCs) can carry even more, surpassing 550,000 tons, or more than three million barrels. Generally, intermediate process streams and finished products require even more tankage than crude oil. In addition, provision must be made for short-term variations in demand for products and also for maintaining a dependable supply of products to the market during periods when process units must be removed from service for maintenance.
Nonvolatile products such as diesel fuel and fuel oils are stored in large-diameter cylindrical tanks with low-pitched conical roofs. Tanks with floating roofs reduce the evaporative losses in storage of gasolines and other volatile products, including crude oils. The roof, which resembles a pontoon, floats on the surface of the liquid within the tank, thus moving up and down with the liquid level and eliminating the air space that could contain petroleum vapour. For LPG and butanes, pressure vessels (usually spherical) are used.
Flares
One of the prominent features of every oil refinery and petrochemical plant is a tall stack with a small flame burning at the top. This stack, called a flare, is an essential part of the plant safety system. In the event of equipment failure or plant shutdown, it is necessary to purge the volatile hydrocarbons from operating equipment so that it can be serviced. Since these volatile hydrocarbons form very explosive mixtures if they are mixed with air, as a safety precaution they are delivered by closed piping systems to the flare site, where they may be burned in a controlled manner. Under normal conditions only a pilot light is visible on the flare stack, and steam is often added to the flare to mask even that flame. However, during emergency conditions the flare system disposes of large quantities of volatile gases and illuminates the sky.
Utilities
A typical refinery requires enough utilities to support a small city. All refineries produce steam for use in process units. This requires water-treatment systems, boilers, and extensive piping networks. Many refineries also produce electricity for lighting, electric motor-driven pumps, and compressors and instrumentation systems. In addition, clean, dry air must be provided for many process units, and large quantities of cooling water are required for condensation of hydrocarbon vapours.
Environmental treatment
The large quantity of water required to support refinery operations must be treated to remove traces of hydrocarbons and noxious chemicals before it can be disposed of into waterways or underground disposal wells. In addition, each of the process units that vent hydrocarbons, flue gases, or particulate solids must be carefully monitored to ensure compliance with environmental standards. Finally, appropriate procedures must be employed to dispose of spent catalysts from refinery processing units.
Bulk transportation
Large oceangoing tankers have sharply reduced the cost of transporting crude oil, making it practical to locate refineries near major market areas rather than adjacent to oil fields. To receive these large carriers, deepwater ports have been constructed in such cities as Rotterdam (Netherlands), Singapore, and Houston (Texas). Major refining centres are connected to these ports by pipelines.
Countries having navigable rivers or canals afford many opportunities for using barges, a very inexpensive method of transportation. The Mississippi River in the United States and the Rhine and Seine rivers in Europe are especially suited to barges of more than 5,000 tons (37,000 barrels). Each barge may be divided into several compartments so that a variety of products may be carried.
Transport by railcar is still widely practiced, especially for specialty products such as LPG, lubricants, or asphalt. Cars have capacities exceeding 100 tons (720 barrels), depending on the product carried. The final stage of product delivery to the majority of customers throughout the world continues to be the familiar tanker truck, whose carrying capacity is about 150 to 200 barrels.
The most efficient mode of bulk transport for petroleum is the network of pipelines that are now found all over the world. Most crude-oil-producing areas are connected by pipeline either to refining centres or to a maritime loading port. In addition, many major crude-oil-receiving ports have extensive pipeline distribution networks to inland refineries. Centrifugal pumps usually provide the pumping power, with booster stations installed along the line as necessary. Most of the major product lines have been converted to fully automated operation, with the opening and closing of valves carried out by automatic sequence controls initiated from remote control centres.
John E. Carruthers A.L. Waddams Lee H. Solomon The Editors of Encyclopaedia Britannica